The part number may be stamped on the blade. If you find a
stamped part number but are unsure if it is the original blade from the
manuafcturer leave the manufacturer as "all Available" above so that the stamped
blade part # can be searched for across aftermarket replacement blades as well
as the Original manufacturer.
  |
Blade length: Measured diagonally |
| |
|
 |
| |
  |
Blade Center Hole: What is the configuration of the holes on the blade where it is attached to the mower deck? Many blades
will have a round hole in the center of the blade and you will need to know its diameter. |
| |
|
| | Many blades will have a round hole in the center of the blade and you will need to know its diameter. | |
 |
| | The center hole may be a 5 point or 7 point star shaped hole. | |
  |
| |
Some center holes may be
square or rectangular. | |
 |
| | The MTD® built blades (Bolens, Cub Cadet, Troy-bilt, White, Yard Machine, and Yardman) may have a 6 point star. Our replacement blade will
have a “Y” shaped center hole which will fit exactly on the 6 point star on the bottom of the blade spindle. | |
 |
| | There are two different sizes of the 6 point star. If your blade spindle has a bolt and lock washer that holds the blade to the
machine you would use the 11/16" star or Y blade. | |
 |
| | If your blade is secured with a large flange nut then you would use the 5/8" star or Y blade. | |
 |
|
| |
 |
Reset Form button: The reset button will clear your
previous selections. |
| |
 |
Feature Filter: Once a selection of blades is displayed, you may further narrow your results
by selecting a specific blade feature. |
| |
|
| |  | |
Stays Sharp Twice as Long - Using exclusive electrofusion technology, OREGON's Fusion® manufacturing process creates an ultra-hard layer at the blade's cutting edge using tungsten carbide, actually embedding it within the blade. |
| |
| |  | |
The Gator Mulcher®  (3-in-1) works by redirecting clippings up and to the center of the blade. This action keeps the clippings in front of
the cutting edge, allowing them to be cut again and again until all that is left are very fine clippings. Unlike conventional mulching blades, the patented design of Gator Mulcher® 3-in-1 blades not only enhances mulching but also improves side discharge and bagging of the clippings.
|
| |
| |  | |
G6™ lawnmower blades include the full range of features offered by OREGON® - including Gator Mulcher® 3-in-1, High Lift (even higher than the standard profile which provides superior mulching, bagging and side discharge), Fusion® stay sharp technology, X-tended Cutting Length™ for improved mulching, and the blades are built out of wider and thicker steel for durability and longer life. |
| |
|
 |
Blade Length Filter: You can use the blade length filter to narrow the results shown. |
| |
 |
OREGON Part Number |
| |
|
 |
| |
 |
Outer Hole: This is the diameter of any holes to the sides of the center
hole. |
| |
|
 |
| |
 |
Center to Center: If there are outer holes; this is the distance
between the centers of those outer holes. |
| |
|
 |
| |
  |
Width and Thickness: Measure both of these near the center of the blade. |
| |
|
 |
| |
 |
Vertical Drop (Sometimes referred to as offset): If you set the blade on a table this is the distance the center of the
blade is above the table top (if any) when the cutting edges are flat on the table |
| |
|
 |
| |
 |
Air Lift: Air lift is the distance the lift panel rises above the cutting edge. |
| |
|
 |
| |
 |
Manufacturer: The name of the manufacturer of the blade being replaced. This will be the name of your mower manufacturer; or if you are replacing an aftermarket blade, the name of that aftermarket manufacturer. |
| |
 |
Show Detail:
Click on "Show Detail” to see application information, corresponding OEM or
Aftermarket part numbers and OREGON® exclusive features. The listing of blades your search returns will
show blades in groups. All blades listed between two solid lines are members of
a group and will fit the same mower application.
|
| |
 |
Blade Image: Clicking on the small blade image will open a window with a larger picture of the blade.
|
| |
 |
Additional blade information: Additional blade usage information |
| |
 |
OEM Number: The corresponding OEM
(Original Equipment Manufacturer) or aftermarket part number. All corresponding
OEM or aftermarket part numbers are shown. Those matching the OEM part number
entered in the selection box will be high-lighted yellow. |
| |
 |
OREGON® Exlusive: OREGON® exclusive Gator Mulcher® blades are designated with a red icon. |
| |
 |
Blade description and features: The full blade description and icons indicating which OREGON® exclusive features this
blade has. Clicking on the feature icons will open a page with more info about
the feature. |
| |
| |
 |
BEFORE SERVICING OR REMOVING BLADES
- Remove and ground spark plug wire
- Disconnect battery at negative terminal. (for electric start engines only)
- Refer to owner's manual and follow safety warnings
- Do not substitute any other bolt for the blade retaining bolt. Blades and blade retaining bolts are specially made for this application.
- Proper torque must be used when tightening the blade retaining bolt; refer to owner's manual. If this safety
precaution is not followed, the blade could come off during operation.
WHILE MOWING
- Immediately inspect blade if abnormal vibration occurs.
GENERAL
- Properly support and secure mower when replacing blade.
- To avoid possible injury, always wear proper eye and hand protection when servicing mower blade.
- Unbalanced or warped blades can cause damage to the mower and/or personal injury. Inspect the blade(s) and replace damaged blades before operating the mower.
|
. We can provide a list of all OREGON® blades, both
exact manufacturer replacement and OREGON® Gator Mulcher® and Fusion® blades
that will work on your mower. 